HPW Hummer H1 Heavy Duty PMD Pump Mounted Driver

DRX5009
$299.95
HPW Hummer H1 Heavy Duty PMD Pump Mounted Driver
Processing...

HPW Hummer H1 Heavy Duty PMD Pump Mounted Driver

DRX5009
$299.95

Normally: $349.95

Would you like to add the #9 resistor for added performance?:

Product Details


The Pump Mounted Driver (PMD) is the weak link in the Hummer H1 6.5L DS fuel pump. PMD failures generally occur due to exposure to excessive heat during engine operation. Attempts to provide for a cooler operating environment for the PMD has resulted in the development of many remote mount PMD solutions, which involve mounting the PMD away from the fuel pump. These solutions still do not address limitations in the original PMD construction. Now, WAP has a new and improved PMD which replaces the original O.E.M PMD on 6.5L DS fuel pumps. Plus, costs less than the original equipment PMD and most remote mounting solutions! HPW DESIGN HAS ADDED A NEW THICKER INSULATION PACKAGE WHICH ALLOW THE PMD TO REMAIN COOLER FOR LONGER LIFE AND YOU GET A 1 YEAR REPLACEMENT WARRANTY.

WHY USE A HPW PMD?

HPW PMD HAS HIGHER TEMPERATURE RATED COMPONENTS, RATED TO 125 DEGREES CELSIUS OPERATING TEMPERATURE VS THE O.E.M. AT 85 DEGREES CELSIUS.

TESTED OPERATING CONDITIONS OF O.E.M. PMD

TEST CONDITIONS O.E.M. PMD

WITH HIGH FUEL LEVEL...............73 C / 163 F

WITH LOW FUEL LEVEL................89 C / 192 F

W/INCLOSED TRAILER................98 C / 208 F

W/NON-OPER. LIFT PUMP..........103 C / 217 F

(TESTING BY A LEADING REMOTE MOUNT SOLUTION PROVIDER)

THESE TEMPS IN EXCEED THE TEMP RATING FOR THE O.E.M. PMD COMPONENTS. REMEMBER THE O.E.M. IS ONLY RATED TO 85 C. TEST RESULTS WERE THE AVERAGE PMD TEMPS AFTER 100KM DRIVING DISTANCE AT 100KMH AND 250 CELSIUS AMBIENT TEMPS USING NEW O.E.M. PMD'S

YOU WILL NOTE THAT NONE OF THE OPERATING TEMPS EXCEED THE 125 DEGREE CELSIUS RATING FOR THE HPW PMD'S FLEXIBLE MATERIAL INSIDE THE HPW PMD ALLOWS FOR EXPANSION AS THE PMD HEATS UP WHICH MEANS LESS STRESS ON INTERNAL COMPONENTS AND BETTER VIBRATION ABSORPTION. THE O.E.M. USES A HARD MATERIAL THAT DOES NOT ALLOW EXPANSION. THICKER HEAT SINK FOR GREATER HEAT DISSIPATION. HPW PMD...11/16" VS 9/16" FOR THE O.E.M. IMPROVED TRANSISTOR MOUNTING ALLOWS FOR MORE SUBSTANTIAL MOUNTING OF THE 2 TRANSISTORS INTERNALLY FOR A TOUGHER, MORE STABLE ASSEMBLY. LESS CHANCE FOR THOSE INTERMITTENT PROBLEM CAUSED BY THE INTERNAL COMPONENTS VIBRATING LOOSE.

FOR MORE PERFORMANCE ADD THE OPTIONAL #9 RESISTOR.

THE #9 RESISTOR IS THE LARGEST VALUE AVAILABLE.UNLIKE GAS ENGINES, WITH THE DIESELS, THE MORE FUEL INJECTED, THE MORE HP PRODUCED. THIS RESISTOR MOUNTS EASILY ON THE PMD (PUMP MOUNTED DRIVER) FOR YOUR FUEL PUMP. CHANGING THE RESISTOR IS JUST LIKE TURNING UP THE FUEL ON THE OLDER MANUAL INJECTION PUMPS. YOU CAN RETAIN YOUR GREAT MILEAGE IF YOU DRIVE NORMALLY. YET IF YOU PUT YOUR FOOT INTO IT,YOU WILL HAVE CONSIDERABLY MORE POWER WHEN NEEDED, BUT YOU WILL SACRIFICE SOME MILEAGE. THE CALIBRATION RESISTOR WAS DESIGNED TO STRADLE THE PMD CONNECTOR PINS AND IS SANDWICHED IN PLACE BETWEEN THE HARNESS AND THE PMD/FSD CONNECTOR. DIESEL ENTHUSIASTS KNOW THAT INCREASING TO A #9 RESISTOR IS A DEFINATE PERFORMANCE BOOSTER.

INSTALLATION INSTRUCTIONS ARE INCLUDED.

OUR PMD FITS HUMMER H1 6.5L TURBO DIESEL MODEL YEARS 1994 TO 2002